Back to Blog
How-to Guides 2026-11-21 Red Dot Photo 0 views

How to Use a Bowens Mount Reflector for Studio Lighting

How to Use a Bowens Mount Reflector for Studio Lighting

Learn how to set up and use a Bowens mount standard reflector for controlled studio lighting, with tips on beam spread and compatibility for Godox LED lights.

What a Standard Reflector Does in Studio Lighting

A standard reflector is one of the most straightforward light modifiers you can use. It concentrates light into a narrower beam than a bare bulb, giving you more control over where the light falls and how it wraps around your subject. The Godox RFT-19 Standard Reflector, for example, has a 30° beam spread and a faceted polished silver interior that helps maximize output while maintaining a relatively tight pool of light.

This type of modifier is useful for portrait headshots, product detail shots, or any scenario where you want to reduce light spill and create a focused, contrast-rich look. Because it uses a Bowens mount, it can attach to a wide range of studio lights, not just Godox models.

Key Specs of the Godox RFT-19 Standard Reflector

  • Godox RFT-19 Standard Reflector Bowen Mount: 30° beam spread, Bowens mount, faceted polished silver interior, 7" diameter. The 30° beam spread is narrower than many standard reflectors (often 40-50°), making it a good choice for isolating a subject or creating a defined light pool. The faceted interior mixes the light slightly for smoother falloff.
    Godox RFT-19 Standard Reflector Bowen Mount
    Godox RFT-19 Standard Reflector Bowen Mount
  • Godox RFT-19 Standard Reflector Bowen Mount: Compatible with Godox LED heads: VL150, VL200, VL300, SL150II, SL200II, FV150, FV200, and other Bowens mount fixtures. If you already own one of those Godox lights, the RFT-19 will mount directly. If you use a different brand with a Bowens mount, it should also fit, but the beam spread and output may vary slightly depending on the light source size.

Setting Up the Reflector

Attaching the RFT-19 to a compatible light is simple: align the three tabs on the reflector's Bowens ring with the corresponding slots on the light's mount, push in, and twist clockwise until it locks. No tools are needed. Because the reflector is lightweight, it won't strain the light's tilt mechanism.

Once mounted, position the light at the desired distance and angle. The 30° beam spread means the light will be more concentrated than a bare bulb or a larger softbox. For a typical headshot, start with the light at a suitable distance from the subject and adjust based on the shadow density you want.

Using the Reflector for a Simple One-Light Portrait

The following steps assume you have a Bowens-mount light (e.g., Godox VL200) and the Godox RFT-19 reflector attached.

  1. Position the light: Place the light at an angle to the subject, at a suitable distance away. The 30° beam will create a defined key light with soft shadows on the opposite side.
  2. Adjust height and angle: Raise the light slightly above eye level and tilt it down toward the subject. This creates a natural-looking shadow under the chin and brow.
  3. Modify the light quality: If the shadows are too harsh, move the light farther away (reduces contrast) or add a diffuser panel between the reflector and subject. If you want more contrast, bring the light closer.
  4. Check the background: Because the beam is narrow, the background may fall off to black if it's several feet behind the subject. For a lighter background, move the subject closer or add a second light.

What the Supplied Information Doesn't Tell You

The Godox RFT-19 is a passive modifier — it has no moving parts, no grid, and no built-in diffusion. The beam spread is fixed at 30°, so you cannot widen or narrow it without swapping reflectors. If you need a wider spread (e.g., for group shots), consider a 50° or 70° reflector. If you need a tighter spot, a 10° or 5° grid reflector would be more appropriate.

Also, while the reflector is compatible with many Bowens mount lights, the actual beam angle and output uniformity depend on the light source's size and design. A larger COB LED may produce a slightly different falloff than a smaller one. Test with your specific light to confirm the look.

Related Articles

Customer Service
Home
Products
Cart
Profile